Homes and commercial properties
New York
Our hands-on restoration team removes water and dries lightweight floors, walls, insulation, and underbelly materials commonly affected in mobile homes.
Signs to keep an eye out for
Before we get to work, if you notice any of these problems, call us before water has more time to spread into nearby materials.
Once we are on the job site, most manufactured homes are decked in particleboard, which swells and loses its bond once it stays wet. Before we get to work, softness means the panel is already failing rather than merely damp.
In plain words, panel walls are joined with battens over the seams instead of taped and painted like drywall.
Once we are on the job site, vinyl covered gypsum panel walls sit directly on the decking, so they wick water upward from the floor.
Before we get to work, the seam where two sections join is the most common water entry point on a multi section home.
To straighten this out, older homes with low slope metal roofs pond water at seams, vents and the edges.
To straighten this out, the furnace and water heater as a rule share one interior closet sitting directly on the decking. In plain words, a slow drip there soaks the panel under an appliance nobody moves.
What happens
Our hands-on restoration team adjusts the work to what got wet, how far the water traveled, and which materials can be saved.
In plain words, we note the home's age, whether it is a single wide or a double wide, and what the deck and the walls are actually made of.
To straighten this out, particleboard decking that has swelled or lost its bond does not come back, and drying it longer will not change that.
In plain words, panel walls come apart at the battens and the bottom course, which lets us dry the wall cavity without wrecking the whole room.
To straighten this out, portable extractors and compact submersible pumps come through a 30 inch doorway and up a set of steps.
In plain words, many manufactured homes run a 100 amp service, which limits how much drying gear the home can actually carry.
Once we are on the job site, water that reaches an in floor supply duct sits there and gets blown through every room.
Talk with a restoration specialist
Describe the source, the impacted rooms, and when you first noticed the damage.
What to expect
Here is how we as a rule handle mobile home water damage near New York.
In plain words, let us know the approximate age, whether it is a single wide or double wide, and where the water is showing.
Your callIn plain words, close the fixture valve, or the main at the lot pedestal if it is above ground and safe to reach.
+5 minutesBefore we get to work, keep people and heavy furniture off any soft area, since wet particleboard loses strength quickly.
+15 minutesTo straighten this out, we confirm the deck material, the wall panel type, the marriage line if there is one, and where the ducts run.
On arrivalTo straighten this out, water comes off hard flooring and out of carpet and padding, and contents get lifted and blocked. Before we get to work, deeper water is pumped first.
First hours on siteBefore we get to work, we tell you which decking sections, wall panels and cabinets are coming out and which are staying.
Same dayBefore we get to work, equipment is placed and the amperage counted before anyone drives away, so your service is not overloaded overnight.
Before we leaveUnderstanding the cost
We spell out the recommended work and price before you approve the job. These examples show what may change the price breakdown.
| Common situation | What the estimate may include | Typical range |
|---|---|---|
| One room of a manufactured home, clean water, extraction plus three to four days of drying | National price breakdown. A supply line or fixture caught quickly, with little or no decking replacement. | $900 to $2,500 |
| Most of a single wide affected, clean water | National price breakdown. Includes extraction, padding removal, wall panel bottom course work and five to seven days of equipment. | $3,000 to $8,000 |
| Double wide with several rooms and decking replacement | National price breakdown. Water across the marriage line, two duct runs and significant decking and panel replacement. | $6,000 to $18,000 |
| Particleboard decking replacement, per square foot | National price breakdown for removing and replacing failed floor decking, before the finish flooring above it. | $3 to $10 |
| Wall panel replacement, per square foot | National price breakdown for vinyl covered gypsum panel sections including batten work. Older patterns may not be matchable. | $2 to $6 |
| Manufactured home work priced by affected area, clean water | National price breakdown. Handy once someone has measured the wet area and given you a number. | $3 to $7 per square foot |
| Belly wrap drained, wet insulation out, underbelly repair coordinated | National price breakdown. Priced and detailed on our under house water removal page, which owns that work plan. | $800 to $3,500 |
| After hours or overnight dispatch charge | National price breakdown. One charge on the first visit, for nights, weekends and holidays. | $100 to $400 |
What the deck is made of
Particleboard decking that has swelled has to be replaced, and that is labor plus material plus flooring above it.
How much of the home is wet
In plain words, pricing follows affected square footage.
Single section or multi section
A double wide is right around twice the area and adds the marriage line as both a leak path and a drying boundary.
How clean the water was
Supply line water is the least damaging case and saves the most material.
Wall panel count
Panel replacement is priced by area and by how many batten lines have to be opened.
Duct involvement
Once we are on the job site, clearing and drying in floor ducts is straightforward.
Why timing matters
Once we are on the job site, water can keep moving into nearby materials even when the surface looks dry.
In plain words, once the panel swells and its bond fails, it stays swollen and weak no matter how long you dry it.
Once we are on the job site, the vinyl film on these panels is effectively a vapor barrier on the room side, so moisture cannot escape toward the air you are drying.
Before we get to work, small air volume means moisture saturates every room within hours, so there is no comfortable dry side to retreat to.
To straighten this out, water left standing inside a supply duct or the crossover duct gets pushed through the home each time the system runs.
Helpful service information
In plain words, start with the short explanation. Once we are on the job site, open a card if you want a little more detail.
Floors are typically decked in particleboard over relatively shallow floor joists, glued and stapled as a system.
Manufactured homes are built to the federal HUD Code, which produces a very different set of materials from a site built house.
Once we are on the job site, that film behaves like a vapor barrier on the room side, so moisture in the gypsum core cannot escape toward the dry air you are creating in the room.
Before we get to work, the vinyl face on a panel wall is the detail that catches inexperienced crews.
A single section home holds a fraction of the air a two story house does, so evaporating water pushes relative humidity up very quickly and evaporation then stalls.
Air volume is the quiet variable in a home this size. A single section home holds a fraction of the air a two story house does, so evaporating water pushes relative humidity up very quickly and evaporation then stalls.
Help near you
Choose your area below, or call (833) 493-2559 and describe what happened.
You may also need
Our hands-on restoration team removes water from homes, protects belongings, and dries affected rooms after leaks, overflows, storms, or appliance failures.
Get a Quote: (833) 493-2559Our hands-on restoration team removes water beneath the home, clears wet debris or insulation, and dries joists, subflooring, and foundation areas.
Get a Quote: (833) 493-2559Our hands-on restoration team removes surface water and dries moisture trapped beneath finished flooring to protect the subfloor and surrounding materials.
Get a Quote: (833) 493-2559Our hands-on restoration team pumps out crawl-space water, removes wet debris or insulation, and dries framing to control moisture beneath the home.
Get a Quote: (833) 493-2559Our hands-on restoration team removes water, damaged materials, and residue, then cleans and dries affected rooms so repair work can move forward.
Get a Quote: (833) 493-2559Our hands-on restoration team finds moisture inside walls and uses targeted drying or controlled removal to protect framing and nearby finishes.
Get a Quote: (833) 493-2559Our hands-on restoration team addresses water damage in rental properties with clear paperwork, moisture numbers, and coordinated cleanup for owners, managers, and tenants.
Get a Quote: (833) 493-2559Our hands-on restoration team controls the source, removes water, protects contents, and stabilizes wet materials to prevent avoidable secondary damage.
Get a Quote: (833) 493-2559Common questions
Once we are on the job site, it depends entirely on the deck material. Before we get to work, most manufactured homes use particleboard decking, and once it has swelled or lost its bond it does not recover, so those sections come out.
To straighten this out, as a national price breakdown, one wet room with a few days of drying commonly runs $900 to $2,500.
Before we get to work, three reasons. Once we are on the job site, the decking is frequently particleboard rather than plywood, and the walls are vinyl faced gypsum panels joined with battens rather than taped drywall.
In plain words, the bottom few inches are as a rule the problem, since panels sit on the deck and wick water upward.
Before we get to work, that is a separate work plan from the work inside your home, and our under house water removal page covers it in full.
Once we are on the job site, extraction as a rule finishes in one to three hours. To straighten this out, drying then takes about three to five days for a typical loss, sometimes less since there is less material.
In plain words, yes, and it is one of the most commonly missed steps. In plain words, supply ducts run inside the floor and the crossover duct links the sections on a double wide, so water sits in them and gets blown through the home.
Talk with a restoration specialist
Describe the source, the impacted rooms, and when you first noticed the damage.
Areas we serve
Our hands-on restoration team assess homes, businesses, and managed properties throughout New York and nearby communities.
View the area on Google Maps